FCC/ISED Advisory

FCC (USA) and ISED (Canada)

This device complies with FCC rules part 15 and Innovation, Science, and Economic Development Canada RSS-210. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference that may be received including interference that may cause undesired operation. WARNING: The transmitter has been tested and complies with FCC and ISED rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device.

1. This device may not cause harmful interference.
2. This device must accept any interference that may be received including interference that may cause undesired operation.
   Warning: The transmitter has been tested and complies with FCC and ISED rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device.

This equipment complies with FCC and ISED radiation exposure limits set forth for an uncontrolled environment. End Users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must be at least 20 cm from the user and must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC (États-Unis) et ISED (Canada)

Cet appareil est conforme aux règlements de la FCC, section 15, et au CNR-210 d’Innovation, Sciences et Développement économique Canada. Le fonctionnement est assujetti aux deux conditions suivantes : (1) cet appareil ne doit pas causer d’interférences nuisibles et (2) cet appareil doit accepter toute interférence reçue, y compris celle qui pourrait entraîner un dysfonctionnement. MISE EN GARDE : L’émetteur a subi des tests et est conforme aux règlements de la FCC et d’ISDE. Les changements ou modifications non approuvés explicitement par la partie responsable de la conformité pourraient rendre caduque l’autorisation de l’utilisateur de se servir du dispositif.

Cet appareil est conforme aux limites d’exposition aux radiations de la FCC et d’ISDE établies pour un environnement non contrôlé. Les utilisateurs finaux doivent respecter les instructions d’utilisation spécifiques pour satisfaire aux exigences de conformité aux expositions de RF. L’émetteur doit se trouver à 20 cm au minimum de l’utilisateur et ne doit pas être situé au même endroit que tout autre émetteur ou antenne ni fonctionner avec un autre émetteur ou antenne.

Have the remote for the garage door or gate you are programming ready to set up a new HomeLink program and follow these steps:

1. Select >  Connectivity > HomeLink on the Pilot Panel then press + ADD NEW HOMELINK.
   Note: Press CANCEL during any step of programming to return to the main HomeLink® screen. No information will be stored.
2. Use the on-screen keyboard to enter a name for your HomeLink®, then press CONTINUE.
3. Prepare your surroundings as instructed on the screen, and press CONTINUE when you are ready to proceed.
   Note: Select Program with D-Mode only if your device requires D-Mode programming per the HomeLink website or operator’s manual.
4. To record the remote signal, press and hold the remote 2 in (5 cm) below the letter L on the front of your vehicle, until the horn sounds and the headlights flash.
5. Press CONTINUE once the Pilot Panel shows that recording is complete.
   Note: The on-screen process will automatically skip this step and proceed to the following test if it detects that your device uses a fixed code.
   Press the LEARN button on the back of your receiver, (removing the cover if needed), to train the receiver. Press CONTINUE on the Pilot Panel.
   Note: A second person can assist with this step since pressing the LEARN button is time-sensitive.
   Note: You can press CONTINUE if your receiver is QuickTrain compatible.
   Note: You will have 30 seconds to test HomeLink after pressing the 'LEARN' or sync button. An error message will display with the option to try again if a signal is not detected within the timeout period.
6. Press the TEST HOMELINK button to test it. You will need to press this three times in total. Wait until you see a check mark before pressing the button a second and third time.

7. The TEST HOMELINK button will temporarily be unavailable during each brief test, while the current test number animates to indicate that it is in progress.

   Note: The device you are programming may respond during any of these three tests. Continue with all three tests.
8. A check will replace the number after a test completes and the TEST HOMELINK button becomes available. Continue through all three tests.
9. The screen will prompt you to confirm whether the device responded after all three tests have completed. Press YES or NO.
   Note: Pressing NO will give you the option to restart the test and contact information for HomeLink Help.
10. You will be brought back to the Connectivity screen if you press YES. Your new HomeLink device will be listed under CONNECTED DEVICES.

Reprogramming a Device

1. Select >  Connectivity > HomeLink on the Pilot Panel, then click the device to be reprogrammed.
2. Press PROGRAM on the device details screen.
3. Follow the steps for programming a device. See Programming Homelink.

The devices can be accessed using the HomeLink menu on the Right Cockpit Panel once they have been programmed to your vehicle.

The HomeLink menu will automatically open when the vehicle is detected within 131 ft (40 m) of a programmed garage door or gate. To manually access it:

1. Press the status bar to expand.
2. Press to open HomeLink.

From this menu, you can:

• Press HOMELINK SETTINGS to add a new device, edit, or remove existing devices. See Renaming or Deleting a Device.
• Press a device name to activate it.

The icon next to a device indicates that a signal has been sent to the door or gate. The menu automatically collapses three seconds after a signal is sent.

Renaming a Program

1. Select >  Connectivity > HomeLink on the Pilot Panel, then choose the device to be renamed.
2. Press the edit icon on the device details screen.
3. Use the on-screen keyboard to edit the device name, then press SAVE to confirm, or CANCEL to return to the previous screen.

Deleting a Program

1. Select >  Connectivity > HomeLink on the Pilot Panel, followed by the device to be removed.
2. Press DELETE on the device details screen.
3. The screen will prompt to confirm whether you wish to delete the selected device. Press DELETE ALL to confirm or CANCEL to return to the previous screen.

Deleting All Programs

1. Select >  Connectivity > HomeLink on the Pilot Panel.
2. The option to DELETE ALL will be available if two or more devices are connected to your vehicle. Press it to continue.
3. The screen will prompt to confirm whether you wish to delete all connected HomeLink® devices. Press DELETE ALL to confirm or CANCEL to return to the previous screen.